ページ : 1 2
Aironet AP1262Nの初期化
続いて、Cisco Aironet AP1262Nを同じ要領で初期化します。
図4.AP1262N上面視
AP1252AGよりも重量は軽く、底面の各ソケットへのアクセスも余裕が設けている印象です。
図5.AP1262N底面視
コンソールケーブルを繋いだら電源を入れます。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 |
r WRDTR,CLKTR: 0x8200083f 0x40000000 r RQDC ,RFDC : 0x80000031 0x00000212 using eeprom values WRDTR,CLKTR: 0x8200083f 0x40000000 RQDC ,RFDC : 0x80000031 0x00000212 using SMSJ ddr static values from serial eeprom ddr init done Running Normal Memtest... Passed IOS Bootloader - Starting system. FLASH CHIP: Numonyx P33 Checking for Over Erased blocks ............................................................................. Xmodem file system is available. DDR values used from system serial eeprom. WRDTR,CLKTR: 0x8200083f, 0x40000000 RQDC, RFDC : 0x80000031, 0x00000212 PCIE0: link is up. PCIE0: VC0 is active PCIE1: link is up. PCIE1: VC0 is active 64bit PCIE devices PCIEx: initialization done flashfs[0]: 155 files, 7 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 31739904 flashfs[0]: Bytes used: 7583744 flashfs[0]: Bytes available: 24156160 flashfs[0]: flashfs fsck took 10 seconds. Reading cookie from system serial eeprom...Done Base Ethernet MAC address: 4c:00:82:e9:8c:de Waiting for PHY auto negotiation to complete... TIMEOUT ! Ethernet link is down. Error: RGMII speed The system has encountered an error initializing the Ethernet port. The system is ignoring the error and continuing to boot. If you abort the system boot process, the following commands will re-initialize Ethernet, TFTP, and finish loading the operating system software: ether_init tftp_init boot Loading "flash:/ap3g1-k9w7-mx.124-25d.JA1/ap3g1-k9w7-mx.124-25d.JA1"...########### |
ここで ESC キーを押して中断。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 |
bad mzip file, unknown zip method Error loading "flash:/ap3g1-k9w7-mx.124-25d.JA1/ap3g1-k9w7-mx.124-25d.JA1" Interrupt within 5 seconds to abort boot process. Boot process failed... The system is unable to boot automatically. The BOOT environment variable needs to be set to a bootable image. C160 Boot Loader (AP3G1-BOOT-M) Version 12.4(23c)JA5, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Compiled Mon 30-Apr-12 13:35 by prod_rel_team ap: |
flash:の中には以前のクラッシュログの残骸がありました。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 |
ap: dir flash: Directory of flash:/ 2 -rwx 5 <date> private-config 3 -rwx 380496 <date> crashinfo_20160607-101417 4 -rwx 64 <date> sensord_CSPRNG1 5 -rwx 368157 <date> crashinfo_20141021-025020 6 -rwx 390328 <date> crashinfo_20131206-024742 7 -rwx 64 <date> sensord_CSPRNG0 9 -rwx 2072 <date> private-multiple-fs 10 -rwx 331 <date> env_vars 11 drwx 512 <date> ap3g1-k9w7-mx.124-25d.JA1 163 -rwx 3351 <date> config.txt 24156160 bytes available (7583744 bytes used) |
AP1252AGと同じファイルを削除・リネームして起動してみるも状況は全く同じなので、こちらも MODE スイッチ起動して初期化することに。
図6.AP1262N MODEボタン
初期化状態の設定は、無線設定に細かな差異が見受けられる程度で、基本的にAP1252AGとほぼ同じです。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 |
no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ap ! logging rate-limit console 9 enable secret 5 $1$g0Np$2iVKulZRReXIZUOcxUkPz. ! no aaa new-model ! ! dot11 syslog ! ! username Cisco password 7 047802150C2E ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache shutdown antenna gain 0 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown antenna gain 0 no dfs band block channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 ip address dhcp client-id GigabitEthernet0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! ! line con 0 line vty 0 4 login local ! end |
Aironet AP1262Nの基本設定
このAPも初期設定をベースに、必要なWiFiプロファイルと機器の基本設定を以下の要領で発行しました。
2.4G帯Dot11Radio0のバンド幅が40MHz非対応であるなど、AP1252AGの時と微妙に異なります。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 |
no dot11 syslog no logging console hostname AP1262N clock timezone +0800 8 username admin secret ######## no username Cisco enable secret ######## dot11 ssid WIFI authentication open authentication key-management wpa version 2 wpa-psk ascii ######## guest-mode interface Dot11Radio0 encryption mode ciphers aes-ccm ssid WIFI channel least-congested 1 6 11 power client max power local max no antenna gain 0 no shutdown ! interface Dot11Radio1 encryption mode ciphers aes-ccm ssid WIFI no antenna gain 0 no shutdown ! line con 0 exec-timeout 0 0 length 0 line vty 0 4 exec-timeout 0 0 login local ! sntp server 118.143.17.82 sntp broadcast client end |
組み上がった設定は以下の通りです。
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 |
no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname AP1262N ! logging rate-limit console 9 no logging console enable secret 5 ############################### ! no aaa new-model clock timezone +0800 8 ! ! no dot11 syslog ! dot11 ssid WIFI authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 7 ############ ! ! ! username admin secret 5 ############################## ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid WIFI ! antenna gain 0 channel least-congested 2412 2437 2462 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid WIFI ! antenna gain 0 no dfs band block channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 ip address dhcp client-id GigabitEthernet0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! ! line con 0 exec-timeout 0 0 length 0 line vty 0 4 exec-timeout 0 0 login local ! sntp server 118.143.17.82 sntp broadcast client end |
created by Rinker
¥3,960
(2024/04/25 06:07:36時点 Amazon調べ-詳細)
ページ : 1 2